Installing a shower column does not require extensive knowledge or experience, so you do not need to hire a plumber to carry out the necessary installation work. Modern shower sets have complete equipment, so the installation is limited to anchoring the column to the wall and connecting the hydraulic supply to the place where the old showerhead was located. Let’s check how this looks in practice.
How to Prepare for Installing a Shower Column?
A new shower column should be tailored to individual needs and include everything you need - including installation elements and screws. Before starting installation work, remember to open the package and check the set of parts. If the set is incomplete, or if any part was damaged during transport, you can exchange the entire set or report the absence of individual elements.
Installing the Rain Shower Head and Showerhead - Drill
The basic tool for installing a shower set is a drill. You will need the right drill bit to make preliminary holes for installation. In the attached instructions, you will find the screw size, based on which you will choose the preferred type of drill bit. If you are installing a shower panel on a tiled wall, you need to use a tip for glass and tiles. To minimize the risk of cracking, remember to reduce the drill speed. Keep our tips in mind, and the installation of the rain shower head and showerhead will go smoothly!
Adjustable Wrench and Pliers - Installation Accessories for the Shower Cabin
Another useful tool when planning the installation of the rain shower head and other components of the shower is an adjustable wrench, which you will use to remove the original showerhead, install the pipes supplying water to the new shower column, and tighten all new connections. Of course, you can use your hands to tighten almost all parts, but the wrench will allow you to perform the final firm turn that will prevent leaks. The last essential tool is pliers, which will help grip and turn small and hard-to-reach connections.
Installation Accessories - How to Avoid Water Leaks?
Plumber’s tape is an essential accessory used to wrap the threads connecting the shower pipes. Properly installed, it creates a seal that is difficult to circumvent, helping to avoid water leaks. You should not forget about silicone sealant, which will fill any cracks between the panel and the shower wall. Moreover, the sealant prevents water from getting behind the shower panel and the formation of mold.
Installing a Shower Column - See How Simple It Is!
If you are ready to install the shower column, start by turning off the valves. The procedure for installing a new shower set in the bathroom can be summarized in a few steps:
- Using a wrench and pliers, grip and start unscrewing the showerhead.
- When the showerhead is loosened enough, you can unscrew it manually.
- Begin rotating and loosening the shower arm using pliers.
- Look for hidden screw holes and then remove them one by one. When everything is disassembled, you will have access to the hot and cold water pipes.
If you plan to reuse the shower arm and showerhead, clean them thoroughly and wait until they are completely dry before storing them.
Installing the Shower Column in a Few Simple Steps
Once the shower is disassembled and prepared for the installation of the panel, you can proceed to carry out the actual work. Depending on the shower panel purchased, some steps may differ, but the installation usually proceeds in a very similar way:
- Check where you will mount the panel and the rain shower head. Use a level to mark the holes.
- If you have a level and someone to help, ask them to hold the level above the showerhead while you ensure it is properly centered.
- Use a drill to make holes.
- Place mounting brackets suited to the size of the holes. Again, use a drill to place the screws in the wall.
- Start connecting the pipes and fittings that will lead from where the showerhead was located to where the pipes run.
- Make sure each connection is wrapped with plumber's tape and tighten it properly to avoid leaks.
- Ensure that the connections from the wall are connected to the correct parts of the panel.
- Before mounting the panel, turn on the water and check for any leaks.
- Attach the shower column to the wall using mounting brackets.
Regardless of whether you plan to install a rain shower or other additional accessories, you can be sure the entire work will go smoothly. So, let's choose the right solutions and compile a list of shower accessories, rain shower, showerhead, etc., and then proceed with the installation work and enjoy a bathroom equipped with a modern shower column.
Related products
