How to Install a Shower Column?

Installing a shower column does not require extensive knowledge or experience, so you do not need to hire a plumber to perform the necessary installation work. Modern shower sets come fully equipped, so installation is limited to anchoring the column to the wall and connecting the water supply to where the old showerhead was. Let's see how this looks in practice.

How to Prepare for Installing a Shower Column?

A new shower column should be tailored to individual needs and contain everything you need, including mounting elements and screws. Before starting the installation work, remember to open the package and check the parts kit. If the set is incomplete or any part was damaged during transport, you can exchange the entire set or report the lack of individual elements.

Installation of Shower Head and Showerhead - Drill

The main tool for installing the shower set is a drill. You will need the appropriate drill bit to pre-drill holes for installation. In the attached instructions, you will find the screw size, based on which you will choose the preferred drill bit type. If installing the shower panel on a tiled wall, you need to use a bit for glass and tiles. To minimize the risk of cracking, remember to reduce the drill's speed. Follow our advice, and the installation of the shower head and showerhead will go smoothly!

Adjustable Wrench and Pliers - Mounting Accessories for Shower Cabin

Another equally useful tool when planning the installation of the shower head and other shower elements is an adjustable wrench, which you can use to remove the original showerhead, install pipes delivering water to the new shower column, and tighten all new joints. Of course, you can use your hands to screw on almost all parts, but the wrench will allow for the last strong turn that prevents leaks. The last essential tool is pliers, which help grasp and turn small and hard-to-reach joints.

Mounting Accessories - How to Avoid Water Leaks?

Plumber's tape is an essential accessory for wrapping the threads connecting shower pipes. Correctly installed, it creates a hard-to-bypass seal that prevents water leaks. Also, don't forget about silicone sealant, which will fill any cracks between the panel and the shower wall. Moreover, the sealant prevents water from seeping behind the shower panel and the formation of mold.

Installing the Shower Column - See How Easy It Is!

When you are ready to install the shower column, start by turning off the valves. The procedure for installing a new shower set in the bathroom can be presented in a few steps:

• Using the wrench and pliers, grab and start unscrewing the shower head.
• When the showerhead is loose enough, you can unscrew it by hand.
• Start turning and loosening the shower arm using pliers.
• Look for hidden screw holes and remove them one by one. When everything is dismantled, you will have access to the hot and cold water pipes.

If you plan to reuse the shower arm and showerhead, clean them thoroughly and wait until they are completely dry before storing them.

Installing the Shower Column in a Few Simple Steps

When the shower is dismantled and prepared for panel installation, you can proceed to the actual work. Depending on the purchased shower panel, some steps may differ, yet the installation generally proceeds in a very similar manner:

1. Check where you will install the panel and showerhead. Use a pencil to mark the holes.
2. If you have a level and someone to help you, ask them to hold the level above the shower head, and make sure it is properly centered.
3. Use a drill to make the holes.
4. Place the mounting brackets according to the hole size. Use the drill again to place the screws in the wall.
5. Start connecting the joints and pipes that will run from where the shower head was and where the pipes run.
6. Ensure each joint is wrapped with plumber's tape and tighten it thoroughly to avoid leaks.
7. Ensure the wall joints are connected to the correct parts of the panel.
8. Before mounting the panel, turn on the water and check for any leaks.
9. Attach the shower column to the wall using the mounting brackets.

Regardless of whether you plan to install a shower head or other additional accessories, you can be sure the entire process will go smoothly. So, we choose the right solutions and compile a list of shower accessories, showerhead, etc., then proceed with the installation and enjoy a bathroom equipped with a modern shower column.